Instant Electric Heater Installation Shire of Yarra Ranges

Guide to Installing a Instantaneous Hot Water Heater

Tankless water heaters, also referred to as demand-type or instantaneous water heaters, provide hot water only when it is needed. Instantaneous water heaters provide a constant supply of hot water. They are typically regarded as more energy-efficient since they don’t generate the standby energy losses associated with storage water heaters. They are also believed to cost homeowners less money in the long run. If you are thinking about installing a hot instantaneous water heater in your home, here are the steps you should follow.

Active Plumbing can supply and install a electric hot instantaneous water heater in your home or office an electric unit.


What we do we clean out the area under your sink to ensure there is room for the tank. Then, cut off the water supply from the water heater as well as the power. Drain the water lines by letting the hot water tap run.


If you require a new tap into the sink, we will need to affix the mounting ring from the underside of the sink with a threaded rod. Include the hex nut, and secure them by tightening. Loosen the compression nut at the cold water stop below the sink, then take out the connection. Install a double compression stop to the water connection, Install the tap in the sink then secure the lines to the sink.

Place the tank near the plumbing and an electrical outlet. As you are keeping the tank in place.

Attach the mounting bracket with a drill and bit, drill some holes and attach the unit with 25 mm timber screws. Suspend the tank on the bracket. Install new pipes and connections for hot and cold water and connect to the tank. install sink tap if supply is for a single sink application, Install a control valve also pressure limiting valve if required. Add the clean vent line to the filter. if required Insert each copper strains from the dispenser to the Y fitting. Secure a compression nut over the tubing. Next, link to the double compression stop that you have previously installed at the current water connection and tighten.

If a power point is available connect power to the power point and test water flow through all the hot water taps and remove any air from the hot water pipes

Finishing Touches

Turn the water supply back on. Open the water stops below the sink, then make sure there are no leaks. Open the cold water tap at your brand new instantaneous hot water heater to wash out the filter. Turn off the cold water tap, Turn on the power then open the water taps till water starts flowing. Check the water temperature and adjust if necessary. If hot water is to be used in a bathroom a tempering valve may be required.

Suburbs we service:
Belgrave, Belgrave Heights, Belgrave South, Chirnside Park, Black Springs, Kilsyth, Lilydale, Montrose, Mooroolbark, Mount Evelyn, Mckillop, Selby, Tecoma, Upper Ferntree Gully, Upwey, Badger Creek, Beenak, Basan Corner, Big Pats Creek, Cambarville, Fifteen Mile, Kel Junction, Montys Hut, Shaw, The Triangle, Chum Creek, Healesville, Coldstream, Coldstream West, Dixons Creek, Don Valley, Fernshaw, Ferny Creek, One Tree Hill, Gilderoy, Gladysdale, Saint Benedicts, Gruyere, Cahillton, Yeringberg, Healesville, Tims Corner, Hoddles Creek, Kallista, Beagleys Bridge, Sassafras South, Kalorama, Launching Place, Lysterfield, Macclesfield, McMahons Creek, Matlock, Menzies Creek, Millgrove, Monbulk, Nathania Springs, Mount Dandenong, Mount Toolebewong, Narre Warren East, Olinda, Harmony Vale, Powelltown, Black Sands, Erreys, Nayook West, Quongup, Reefton, Upper Yarra Dam, Sassafras, Sassafras Gully, Seville, Seville East, Killara, Sherbrooke, Silvan, Burleigh, Silvan South, Steels Creek, Tarrawarra, The Patch, Three Bridges, Toorongo, Tremont, Wandin East, Wandin North, Wandin Yallock, Warburton, Old Warburton, Warburton East, Wesburn, Britannia Creek, Tarrango, Woori Yallock, Yarra Glen, Tanana, Yarra Junction, Yellingbo, Parslow, Yering